Exactly How to Remove and Change a Tub
Contact UsJust how do you actually feel when it comes to Installing A Bathtub?
Installing a bath tub isn't precisely rocket science, yet it does call for solid plumbing, woodworking, and also in some cases, tiling abilities. Replacing an old tub with a brand-new one is also a reasonably hard job. If the old bathtub is readily easily accessible, the task can move quickly; if you need to open up a wall to eliminate the old bathtub and position the brand-new bath tub, the task is a lot harder. In either instance, the project is within a house handyman's skills, although you will require an assistant to move out the old bathtub and also set in the new one. Make certain you have actually qualified yourself for the task and also are comfortable trying it. Rather than hiring a specialist to take control of a halfway-completed project, it is better to think about using one prior to you begin. Chances are you may require a specialist plumber to make tube connections.
This post will certainly aid you install a new tub in your shower room if you have actually currently acquired a brand-new bathtub and don't need to transform the arrangement of your previous water supply pipes.
Your tools as well as product list must consist of the following:
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installment, after that the first thing you need to do is detach the water system. After doing so, switch on the faucets to drain pipes any type of water staying in the system. The procedure of eliminating the existing faucets can be rather troublesome because of the restricted gain access to that is typically the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipes to the taps. Have a cloth ready for the continuing to be water that will come from the pipes. When the supply pipes have actually been removed, use the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary faucets from transforming during this process. As soon as the faucets have actually been eliminated, the holes in the bath/basin will need to be cleansed of any type of old sealing compound.
Before moving on to fit the brand-new faucets, compare the pipe links on the old faucets to the new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the new faucets to fit.
Suitable New Taps
If the tails of the new faucets are plastic, then you will require a plastic port to avoid damage to the string. One end of the port fits on the plastic tail of the tap as well as the other end gives a link to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly need decreasing couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next, place the tap in the placing opening in the bath/basin ensuring that the washing machines are in area between the tap and also the sink. Secure the faucet in place with the manufacturer supplied backnut. As soon as the tap is securely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with typical tap adapters. The former kind should be connected to the tap finishes first, tightening up only by hand. The supply pipes can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Setting up the Bathtub
Utilizing both wooden boards under its feet, put the bath tub in the required position. The wooden boards are handy in uniformly spreading out the weight of the tub over the location of the boards as opposed to focusing all the weight onto 4 small points.
The following goal is to make certain that the bathtub is leveled all round. This can be accomplished by checking the spirit level and also adjusting the feet on the tub till the level reads degree.
To mount taps, fit all-time low of the outermost versatile faucet connector to the suitable supply pipeline by making a compression join; then do the very same for the other tap.
Turn on the water and inspect all joints and also new pipework for leaks and also tighten them if essential. Load the bath tub as well as likewise examine the overflow electrical outlet and also the regular electrical outlet for leakages.
Ultimately, deal with the bathroom paneling as defined in the supplier's user's manual. Tiling and also securing around the tub must wait up until the tub has been made use of at the very least when as this will certainly resolve it right into its last setting.
Getting ready for the Setup
Firstly, the supporting frame supplied with the bath ought to be fitted (if required) according to the manufacturer's instructions. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is essential to see to it that if the faucet includes a plastic washer, it is fitted in between the bath and the faucets. On a plastic bathroom, it is additionally reasonable to fit a supporting plate under the faucets system to prevent pressure on the bathtub.
Fit the flexible faucet ports to the bottom of the two faucets utilizing 2 nuts as well as olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet with the hole in the bath. Use the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Make sure you use all of the provided washers.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath should currently prepare to be suited its final position.
Tiling Around the Bath tub
In the area where the bath fulfills the ceramic tile, it is needed to seal the joins with a silicone rubber caulking. This is necessary as the fitting can move sufficient to fracture a rigid seal, causing the water to penetrate the wall surface in between the bathroom as well as the tiling, resulting in problems with dampness and also feasible leakages to the ceiling listed below.
You can pick from a range of coloured sealants to blend in your fixtures and also installations. They are marketed in tubes and also cartridges, as well as are capable of sealing voids as much as a width of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with twists of soaked newspaper or soft rope. Bear in mind to constantly fill the bathtub with water prior to sealing, to allow for the activity experienced when the bathtub is in usage. The sealant can crack fairly very early if you do not think about this motion before securing.
Alternatively, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally quickly offered on the market. It is suggested to fit the floor tiles utilizing water-resistant or waterproof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I have been very fascinated by How to Install a Bathtub: Install an Acrylic Tub and Tub Surround and I hope you enjoyed reading the entire article. If you please set aside a second to promote this write-up if you enjoyed it. I praise you for your time. Don't hesitate to visit our site back soon.
Source This Article